Errors and sub-errors of Sharp AL-2030, AL-2040CS, AL-2050CS photocopiers | en.Relenado

Errors and sub-errors of Sharp AL-2030, AL-2040CS, AL-2050CS photocopiers

Here are the best error and sub-error for solver all the problem with you Sharp copy.

With this post we will be able to identify a wide range of errors in Sharp photocopiers, as well as finding a possible solution.

If you need any kind of solution get in contact with us by leaving a comment and we will do everything in our hands to post a solution that meets your need.

Error E1

Sub error:

E1-00: IMC communication problems


Details: A failure in communication between the CPU and the IMC.
Cause: IMC failure. IMC default memory / data abnormality
Solution: Replace the PTP MCU with new one.

E1-10: IMC problems

Details: A failure in the IMC
Cause: Because chip USB error / CODEC error en el IMC.
Solución: Vuelva a colocar el PTP MCU con una nueva.

E1-13: IMC flash ROM error

Details: A failure in the IMC ROM flash.
Cause: IMC failure
Solution: Replace the PTP MCU again with a new one. If the download of the program is abnormally terminated, an error may occur. Download the program again to avoid this.

E1-81: IMC Interface communication error (parity)

Details: A parity error in the communication between the CPU and the IMC.
Cause: IMC failure. IMC default memory / data abnormality
Solution: Replace the PTP MCU with new one.

E1-82:  IMC Interface communication error (overflow)

Details: An overflow error in the communication between the CPU and the IMC
Cause: IMC failure. IMC default memory / data abnormality
Solution: Replace the PTP MCU with new one

E1-84: IMC Interface communication error (Framing)

Details: A framing error in the communication between the CPU and the IMC
Cause: IMC failure. IMC default memory / data abnormality
Solution: Replace the PTP MCU with new one

Error E7

Sub error:

E7-01: Duplex memory setup model error, memory undetected error

Cause: The memory is not set up properly or the memory capacity does not meet duplex the setting (6M).
Solution: Set the SIM 26-39 code number to 2

E7-02: LSU problems

Details: BD signal of the LSU cannot be detected in a given cycle. (Always OFF or always ON)
Cause:
LSU connector or LSU harness default or disconnection.
Motor rotation polygon laser beams are not generated normally. MCU PLP failure.
Solution:
Check the connection of the LSU.
Run SIM 61-03 to check the operations of LSU.
Check the polygon motor rotates normally.
Check that laser emitting diode generates laser beams.
Place the LSU unit again.
Place the l PTP MCU.

E7-10: Shading problems (Black correction)

Details: The black CCD analysis level is abnormal when shading.
Cause: Improper connection of the CCD unit flat cable CCD unit abnormality MCU abnormality PLP.
Solution: Check the flat connection cable to the unit CCD. Check the CCD unit.

E7-11: Shading problems (White correction)

Details: The white CCD analysis level is abnormal when shading.
Cause:
Improper connection of the CCD unit flat cable
Dirt on the mirror, the lens, and the white reference plate
Copy lamp lighting abnormality
CCD unit abnormality
MCU PLP abnormality
(When occurred in the SPF / RSPF scan position.)
Improper installation of the mirror unit
Solution:
Clean the mirror, lens, and the white reference plate.
Check the amount of light and the illumination state of the copy lamp (SIM 05-03).
Check the PLP MCU.

E7-16: Abnormal laser output

Details: When the laser output is stopped, HSYNC is detected.
Cause: Laser abnormality MCU PLP abnormality.
Solutions: Check the laser emitting diode operation. Replace the PTP MCU.

Error F5

Sub error:

F5-02: Copy lamp lighting abnormality

Details: The copy lamp does not light
Cause: Copy lamp abnormality
Copy lamp harness abnormality
CCD PWB harness abnormality
Solution:
Use the SIM 5-3 to check the operation of the Copy lamp.
When the copy light is turn on upwards.
Check the mallet and the connector between the CCD unit and the PTP MCU.
When the copy light does not turn on
Check the mallet and the connector between the lamp and the copy PTP MCU.
Place the copy lamp unit again
Place the PTP MCU again.

Error H2

Sub error:

H2-00: open Thermistor

Details:
The thermistor is open.
The fusing unit is not installed.
Cause:
Thermistor abnormality
PLP control abnormality
Fusion section disconnect connector
The fusing unit is not installed.
Solution:
Check mallet and connector between the thermistor and the PLP.
Use SIM 14 to clear the screen of self-diagnosis.

Error H3

Sub error

H3-00: Detection roller of high temperature heat

Details: Higher fusion temperature to 240 ° C
Cause:
Thermistor abnormality
PLP control abnormality
Fusion section disconnect connector
Solution:
Use SIM 2.5 to check the operation of the heater lamp flashes.
When the light flashes normally.
Check the thermistor and the harness.
Check the thermistor input circuit on the PTP control.
When the indicator stays on.
Check the PLP power and the control lamp circuit in the PTP MCU.
Use SIM 14 to clear the screen of self-diagnosis.

Error H4

Sub error

H4-00: Roller heat detector detects low temperature

Details:
1)  When the target temperature (165°C) is not achieved in 55 seconds after starting the heating.
2) When the temperature below 100 ° C for 300 ms is detected under the ready print
State.
When talking about after the heating talks not only about the power supply, but also about restoring the closure and the side near the door (The generation time of H4 is not limited to the power supply.) It means, look for all possibilities that can be heating the printer.

Cause:
Thermistor abnormality
Heater lamp abnormality
thermostat abnormality
PLP control abnormality

Solution:
Use SIM 2.5 to check the operation of the heater lamp flashes.
When the light flashes normally.
Check the thermistor and the harness.
Check the thermistor input circuit on the PTP control.
When the lamp does not light.
Check for disconnection of the lamp heater and thermostat. Check the switch.
Check the power PLP and the lamp circuit control in the PTP MCU.
Use SIM 14 to clear the screen of self-diagnosis.

Error L1

Sub error

L1-00: Feeding is not completed within the specified time after starting the feeding time. (The scan head locking chopper is locked)

Details:
The white and the black area of the shading plate mark are used to obtain the difference in the CCD level values for the assessment of the blocking. When the difference in it is in the black levels and it is small, it is considered that the black point could not be packaged by padlock and error code "L1" is displayed.

Cause:
The scan head is locked by the lock switch.
Mirror unit abnormality
The scanner cable is disconnected.
The origin detection sensor abnormality
Mirror engine harness abnormality

Solution:
Check to confirm that the scan head locking switch is released.
Use SIM 1-1 to check reciprocal mirrors operations.
When the mirror is not fed.
Check for disconnection of the scanner cable.
Check mallet and connector between the mirror motor and PTP MCU.
Place the mirror unit again.
Place the PTP MCU again.
When the mirror is fed.
Use SIM 1-2 to check the mirror position sensor at home.

Error L3

Sub error

L3-00: Scanner returning problems

Details:
When the mirror base is returned for the specified time (6 sec) in mirror initializing after connecting power, the mirror home position sensor (MHP) does not light. Or when the mirror base is returned for the specified time (about 6 sec) after start of copy return, the home position sensor mirror (MHP) does not light.

Cause:
Mirror unit abnormality
Scanner disconnections
Origin detection sensor abnormality
Mirror engine harness abnormality

Solution:
Use SIM 1-1 to check reciprocal mirrors operations.
When the mirror does not return.
Entry for disconnection of the scanner cable.
Check mallet and connector between the mirror motor and PTP MCU.
Place the mirror unit again.
Place the PTP MCU again.
When the mirror is fed.
Use SIM 1-2 to check the mirror position sensor at home.

Error L4

Sub error

L4-01: Lock detection main motor

Details:
When the main motor pulse encoder is not detected during 100 sec.
Cause:
Main motor unit abnormality
Improper connection or disconnection of the main motor and harness.
MCU PLP abnormality
Solution:
Use SIM 25-01 to check the operations of the main motor.
Check the connection of the main engine harness / connector.
Place the main motor again.
Place the PTP MCU again

L4-32: Extractor motor stall detection problems

Details:
Error detection is initiated after 2 seconds after starting of rotation of the exhaust fan motor.
1) The state of continuous rotation of 250 ms is not detected during a 1 sec after starting detection
2) When the lock sensor (on the exhaust fan) detects the HIGH level (unstable) after detection lockout state (steady state)

Cause:
Exhaust fan motor connector connection without problems
Exhaust fan motor problems
MCU PLP problems

Solution:
Exhaust fan motor connector connection check
Engine spare Exhaust Fan
Place the PTP MCU again.

Error L6
Sub error

L6-10: Polygon Motor lock detection

Details:
The lock signal (signal specified rpm) does not return within a certain time (about 20 seconds) after the rotation of the polygon motor starts.

Cause:
Polygon motor unit abnormality
Improper connection or disconnection of the polygon motor and harness
MCU PLP abnormality

Solution:
Use SIM 61-1 to verify the operations of the polygon motor.
Check the connection of the polygon motor harness / connector.
Place the polygon motor again.
Place the PTP MCU again.

Error U2

Sub error

LU-04: EEPROM read / write error (error of serial communication)

Details:
EEPROM read / write error (error of serial communication)
Cause:
EEPROM abnormality
Solution:
Check that the EEPROM is tight.
Use SIM 16 to cancel the job.
Place PTP MCU again.

LU-11: Revision of sum error counter (EEPROM)

Details:
Error of the sum counter area in EEPROM
Cause:
EEPROM abnormality
Solution:
Check that the EEPROM is tight.
Use SIM 16 to cancel the job.
Place the PTP MCU again.

COMMENTS

android,3,apple,4,black,2,brother,43,canon,261,cartridge,53,chromebook,2,connectors,9,continuous Ink system,47,copier,6,copy machine,8,dell,7,deskjet,4,drivers,110,epson,188,errors,189,fix,16,google,8,hewlett-packard,44,hp,144,injectors,3,ink,95,kodak,1,konica,1,kyocera,5,laser,21,lexmark,29,linux,1,macintosh,6,mobile,2,multifunction printer,13,pdf,1,print heads,19,printer,198,refill,89,reset,169,samsung,13,scan,30,sharp,10,software,5,toner,18,tricolor cartridge,19,tutorial,161,ubuntu,3,usb cable,5,waste ink pad,8,wicreset,2,windows,39,wireless,9,yahoo,1,
ltr
item
en.Relenado: Errors and sub-errors of Sharp AL-2030, AL-2040CS, AL-2050CS photocopiers
Errors and sub-errors of Sharp AL-2030, AL-2040CS, AL-2050CS photocopiers
Here are the best error and sub-error for solver all the problem with you Sharp copy.
en.Relenado
https://www.en.relenado.com/2015/01/errors-and-sub-errors-of-sharp-al-2030-al-2040cs-al-2050cs-photocopiers.html
https://www.en.relenado.com/
https://www.en.relenado.com/
https://www.en.relenado.com/2015/01/errors-and-sub-errors-of-sharp-al-2030-al-2040cs-al-2050cs-photocopiers.html
true
7372395622910312012
UTF-8
Loaded All Posts Not found any posts VIEW ALL Readmore Reply Cancel reply Delete By Home PAGES POSTS View All RECOMMENDED FOR YOU LABEL ARCHIVE SEARCH ALL POSTS Not found any post match with your request Back Home Sunday Monday Tuesday Wednesday Thursday Friday Saturday Sun Mon Tue Wed Thu Fri Sat January February March April May June July August September October November December Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec just now 1 minute ago $$1$$ minutes ago 1 hour ago $$1$$ hours ago Yesterday $$1$$ days ago $$1$$ weeks ago more than 5 weeks ago Followers Follow THIS PREMIUM CONTENT IS LOCKED STEP 1: Share. STEP 2: Click the link you shared to unlock Copy All Code Select All Code All codes were copied to your clipboard Can not copy the codes / texts, please press [CTRL]+[C] (or CMD+C with Mac) to copy