How to install printer ink system Canon PIXMA MG2410 | en.Rellenado

How to install printer ink system Canon PIXMA MG2410

Advertisements
The Canon PIXMA MG2410 printer made for the replacement of the previous Canon PIXMA MP230 among other models in all Latin America, Russia and other countries have different names although some factors not make system setup easy.
canon PIXMA MG2410 printer with ink system
canon PIXMA MG2410 printer with ink system
But we should not worry, what matters most for a printer like I said in many publications is the cartridge and the number of pages that we, as you know canon cartridges so far and a remarkable example of this is the PG- 210 / CL-211 / PG-140 / CL-141 cartridges were and are resistance.
This printer has changed some other features that Canon had kept PIXMA models, such as the rest of the cartridges will now be on the left side of the printer, on the right will extractors allow to clean ink while the printer does its job.

Apparently the material has changed this printer as the noise increased significantly, we could suppose it to be a cheap inkjet printer, and is actually the cheapest of multifunctional so far.

So if this is completely different black ink cartridge, which by the way for those who fill these ink cartridges would be of interest as filling our publication No. PG-145 / PG-145 XL is compatible with Canon and model PIXMA MG2510.
where fill pg-145 black
where fill pg-145 black
Too bad because we can not do this cartridge hole at the top, but doing work correctly by extreme left of it as show below.

Here you will see a procedures for system installation, you must open the printer but not much, just be careful with disassembling the printer as some technical knowledge is required. But first we start with the preparation of cartridges for mounting on the printer.

Step No. 1 — Prepare ink cartridges (make holes)

As mentioned in the previous paragraphs, it is necessary to make a hole on the right end of the cartridge Canon PG-145 ink as it will not allow above as above compatible with such printers.

Before we seal with hot glue the hole is marked with an arrow in the picture above, do it very carefully and delicately, it should be properly sealed to keep out air and ink cartridge does not return through the hoses to the ink tanks.
hole plugged into cartridge pg-145
hole plugged into cartridge pg-145
List five boxes above and which should be sealed completely to prevent air from escaping, using lighting also make a visual investigation.
pg-145 cartridge with perforation
pg-145 cartridge with perforation
With such a tool which looks at the image, better known as the drill bit, we will drill cartridge, so that it fits the plug correctly and avoid air out of the cartridge.

Step No. 2 — Preparation of tri-color cartridge

Like the old ink cartridges, drilling up of tiny holes that are hardly visible, use the tool having the above image (drill bit) remember not to make big hole to avoid damaging the cartridge so that it can not be solve.

If you are interested to know where the color cartridge, we recommend looking at our publication to be safer position, image following drilling results tricolor cartridge.
color cartridge with perforations and their respective plugs
color cartridge with perforations and their respective plugs

Step No. 3 — Disarm the printer to correctly position the route hoses

Here you should be very careful if you do not know much how to disarm a printer without hurting it, just follow the steps and everything will be fine, if you do not feel fit to do fence at the end of this publication and see how to do it without disassembling printer — at least not as much as here — see image below.
first steps to disarm canon pixma mg2410
first steps to disarm canon pixma mg24100
Then you remove the screws that hold the top printer cover, below the top tray we have removed.

Now we remove the cover where are the buttons on the printer — that is on, reset or deletion, color copying and black etc. — Should do some brute force but not enough to damage the printer or break the plastic, look at the picture and have example of how to do better.
remove the screw under the cap in the red circle
remove the screw under the cap in the red circle
As you can see below this cover is a red circle indicating the position of a screw which must be removed to remove the cover completely.

Step No. 4 — Do get the ink cartridges and connecting hoses to them correctly

This is when you should not confuse the colors before attaching the hose to the cartridges, make ink each cartridge arrives and verify that this does not return to the tank — if it's a good drill right size cartridges will not return the ink — matters a lot how to place the hose to reach the cartridge, look at the image below.
cartridges hoses connected to the ink system
cartridges hoses connected to the ink system
Place cartridges hoses and everything as it is shown in the following image, this way never jam cartridges hose much less block the way and swing the head.

You should place two clips to hold the hoses on top of the head, in the image below you see an example of this, you should take a walk around the head going around behind and going ahead. view image
hoses around the carriage
hoses around the carriage

Step No. 5 — Place the respective hoses and hose clips to grip the printer door

Now the hoses attached to the carriage, the look you have is the former, then you must place a clip to hold the hoses in the printer door as is the image below.
hoses connected at the front door
hoses connected at the front door
Now the amount of hose needed by the printer so that the head is not binding and reaches the ends is placed correctly, put the top cover of the printer and connect the cables to properly operate the equipment.

If you experience a problem write a comment, we're here to help, if it considers it necessary to improve this information help us.

Advertisements

2 comments:

  1. Hello. I have a Canon Pixma 2410. Where can i buy the CIS system for my printer? I want one. Please help.

    ReplyDelete
  2. Hello. I have a Canon Pixma MG2410. Could someone please tell me where I can buy a CIS system for my MG2410. Please help me. Thanks.

    ReplyDelete